RGBlink NDI PTZ Camera Controller (RGBBKT) User Manual

1. تعارف

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of the RGBlink NDI PTZ Camera Controller (RGBBKT). This device is designed for professional video production environments, offering comprehensive control over various PTZ cameras using multiple protocols.

Image 1.1: RGBlink NDI PTZ Camera Controller (RGBBKT).

2. سیٹ اپ

Follow these steps to set up your RGBlink NDI PTZ Camera Controller.

2.1 پیک کھولنا اور ابتدائی معائنہ

• پیکیجنگ سے تمام اجزاء کو احتیاط سے ہٹا دیں۔
• تصدیق کریں کہ پیکنگ لسٹ میں درج تمام اشیاء موجود ہیں۔
• Inspect the controller for any signs of physical damage. If damage is found, contact your dealer immediately.

2.2 کنٹرولر کو جوڑنا

The RGBlink NDI PTZ Camera Controller supports various connection methods for power and camera control.

• ایتھرنیٹ پر طاقت (PoE): Connect a single RJ45 Ethernet cable from a PoE-enabled network switch to the controller's LAN port. This provides both power and network connectivity.
• بیرونی پاور اڈاپٹر: If PoE is not available, connect the provided power adapter to the DC 12V input port and to a power outlet.
• کیمرہ کنکشن:
  • Ethernet (IP Control): Connect PTZ cameras to the same network as the controller via RJ45 Ethernet cables. The controller supports VISCA over IP, ONVIF v2.42, and NDI v5.5 protocols.
  • Serial Control: For cameras supporting serial communication, use RS232, RS422, or RS485 interfaces. Connect the appropriate cables from the controller's serial ports to the cameras.

Image 2.1: Rear panel connections including RS-232, RS-422, LAN (PoE), and Power Input.

تصویر 2.2: مثال کے طور پرample connection diagram showing PTZ Controller, PoE Switch, PTZ Cameras, Audio Mixer, and Computer.

Image 2.3: Diagram illustrating IP camera connections via a network switch.

2.3 نیٹ ورک کی تشکیل

For IP-based camera control, ensure the controller and cameras are on the same network segment. The controller supports automatic detection of NDI-enabled PTZ cameras.

• Access the controller's web انٹرفیس میں اپنا IP ایڈریس درج کرکے a web browser. (Refer to the device's display or network tools to find the IP address).
• The default login credentials are typically 'admin' with a blank password. It is recommended to set a strong password immediately.
• کے اندر اندر web interface, configure camera protocols (e.g., ONVIF, VISCA over IP) and enter camera-specific user credentials if required.

Image 2.4: NDI|HX camera search and control interface on the controller.

3. آپریشن

This section details the operational functions of the RGBlink NDI PTZ Camera Controller.

3.1 اوورview کنٹرولز

The controller features a 3.49" LCD display, a 3D joystick, various knobs, and a numeric keypad for intuitive control.

Image 3.1: The controller's 3.49-inch LCD display.

تصویر 3.2: تفصیلی view of the 3D joystick and multi-function knobs.

Image 3.3: Layout of the controller's buttons and numeric keypad area.

3.2 کیمرے کا انتخاب

• فوری سلیکٹ بٹن: Use the dedicated CAM 1-5 buttons for quick selection of up to 5 cameras.
• عددی کی پیڈ: For cameras beyond the quick select buttons (up to 255), press the CAM ID۔ button, then enter the camera number using the numeric keypad, and press داخل کریں۔.

Image 3.4: The controller's ability to manage multiple cameras.

3.3 PTZ کنٹرول

• جوائس اسٹک: The 3D joystick controls pan (left/right), tilt (up/down), and zoom (rotate the joystick).
• پی ٹی اسپیڈ نوب: Adjusts the gimbal movement speed for pan and tilt.
• Zoom Knob: Provides precise zoom control, especially useful in preview موڈ

3.4 Image Parameter Adjustment

• IRIS/SHUTTER Knob: Rotate to adjust aperture and shutter speed. Press to switch control modes.
• R/B GAIN Knob: Rotate to adjust red and blue gain. Press to switch control modes.
• FOCUS Button: دبائیں آٹو فوکس button to switch the camera to auto focus mode.
• EXPOSURE Button: Cycles through exposure modes (Aperture Priority, Shutter Priority, Gain Priority, Manual Exposure, Auto Exposure).
• BACKLIGHT Button: Toggles the camera's backlight mode.
• WHITE BALANCE CYCLE Button: Cycles through white balance modes (Indoor, Outdoor, Manual, Auto).
• ONE PUSH TRIGGER Button: When white balance is set to "One-Push White Balance", press this button to initiate a one-push white balance calibration.

Image 3.5: Functions of buttons and knobs on the left side of the controller.

Image 3.6: Functions of buttons and knobs on the right side of the controller, including preset controls.

3.5 پریسیٹس

• SET PRESET Button: Press to enter preset position mode. Use the numeric keys to enter the preset number (0-9) and press داخل کریں۔ بچانے کے لیے دبائیں ای ایس سی باہر نکلنے کے لیے
• CALL PRESET Button: Press to enter preset recall mode. Use the numeric keys to enter the preset number (0-9) and press داخل کریں۔ to recall. Press ای ایس سی باہر نکلنے کے لیے
• The controller supports saving and recalling up to 255 presets per camera.

3.6 مینو نیویگیشن

• مینو بٹن: Press to open or close the camera settings menu. In menu control mode, the joystick controls navigation (up, down, left, right), داخل کریں۔ confirms selections, and ای ایس سی acts as a back button.

4 دیکھ بھال

Proper maintenance ensures the longevity and optimal performance of your RGBlink NDI PTZ Camera Controller.

4.1 صفائی

• Use a soft, dry cloth to clean the exterior of the controller.
• ضدی گندگی کے لیے، قدرے ڈیampur پانی کے ساتھ کپڑے یا ہلکے، غیر کھرچنے والے صفائی کے محلول۔
• Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the surface and display.
• Ensure no liquids enter the device through openings or ports.

4.2 اسٹوریج

• When not in use for extended periods, store the controller in a cool, dry place away from direct sunlight and extreme temperatures.
• آلے کو دھول اور نمی سے بچائیں۔

5 خرابیوں کا سراغ لگانا

یہ سیکشن عام مسائل کا حل فراہم کرتا ہے جن کا آپ کو سامنا ہو سکتا ہے۔

5.1 کوئی طاقت نہیں۔

• طاقت کا منبع چیک کریں: یقینی بنائیں کہ پاور اڈاپٹر کنٹرولر اور ورکنگ پاور آؤٹ لیٹ دونوں سے محفوظ طریقے سے جڑا ہوا ہے۔
• PoE Check: If using PoE, verify that the Ethernet cable is connected to a PoE-enabled port on your network switch and that the switch is powered on.
• کیبل کی سالمیت: Inspect the power cable and Ethernet cable for any damage.

5.2 Cannot Control Camera

• نیٹ ورک کنیکٹیویٹی: For IP cameras, ensure the controller and cameras are on the same network and can communicate. Check network cables and IP addresses.
• پروٹوکول کی مماثلت: Verify that the correct control protocol (e.g., VISCA over IP, ONVIF, NDI, Pelco-D/P) is selected on both the controller and the camera.
• کیمرا ID: Ensure the correct camera ID is selected on the controller.
• لاگ ان کی اسناد: If the camera requires authentication, confirm that the correct username and password are configured in the controller's web انٹرفیس
• سیریل کنکشن: For serial control, check RS232/RS422/RS485 cable connections and ensure baud rates and addresses match between the controller and camera.
• فرم ویئر: Ensure both the controller and cameras have the latest firmware installed. Visit the RGBlink support webاپ ڈیٹس کے لئے سائٹ.

5.3 LCD Display Issues

• کوئی ڈسپلے نہیں: یقینی بنائیں کہ کنٹرولر آن ہے۔
• مدھم ڈسپلے: Check if there are any brightness settings on the controller that can be adjusted.

6. وضاحتیں

Image 6.1: Controller dimensions and typical usage environments.

Image 6.2: Visual representation of supported protocols including RJ45, RS485, RS422, RS232, ONVIF, NDI, Pelco-D, Pelco-P, and Visca.

7. پروڈکٹ ویڈیو ڈیموسٹریشن

Watch the official product video for a visual demonstration of the RGBlink NDI PTZ Camera Controller's features and operation.

8. وارنٹی اور سپورٹ

For warranty information, technical support, or service inquiries, please contact RGBlink customer service or visit their official webسائٹ

• مینوفیکچرر: Xiamen RGBlink Science & Technology Co.,Ltd.
• سرکاری Webسائٹ: www.rgblink.com (نوٹ: یہ پلیس ہولڈر ہے۔ URL, please refer to your product packaging or official documentation for the correct support webسائٹ)
• رابطہ کی معلومات: Refer to the RGBlink official website for the most current contact details for technical support and warranty claims.