GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

تعارف

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

حفاظتی معلومات

انتباہ: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• یہ آلہ نیشنل الیکٹرک کوڈ اور مقامی ضوابط کے مطابق تنصیب کے لیے ہے۔
• Do not use in wet locations or where directly exposed to water.
• صرف اندرونی استعمال کے لیے۔

پیکیج کے مشمولات

• GoControl WS15Z5-1 Z-Wave Wall Switch
• تنصیب کے پیچ
• Wire Nuts (may vary by package)
• صارف دستی (یہ دستاویز)

سیٹ اپ اور انسٹالیشن

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. پرانا سوئچ ہٹائیں: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. تاروں کی شناخت کریں:
   • لائن (گرم): عام طور پر سیاہ، سرکٹ بریکر سے آتا ہے.
   • لوڈ: Usually black, going to the light fixture or appliance.
   • غیر جانبدار: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • زمین: عام طور پر سبز یا ننگے تانبے۔
4. نیا سوئچ جوڑیں: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • مربوط کریں۔ لائن wire to the terminal marked "LINE".
   • مربوط کریں۔ لوڈ wire to the terminal marked "LOAD".
   • مربوط کریں۔ غیر جانبدار wire to the terminal marked "NEUTRAL".
   • مربوط کریں۔ گراؤنڈ wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. ماؤنٹ سوئچ: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. وال پلیٹ انسٹال کریں: Attach the new or existing wall plate.
7. بجلی کی بحالی: سرکٹ بریکر پر پاور کو دوبارہ آن کریں۔

شکل 1: سامنے view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle ایک بار. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

سوئچ کو آپریٹ کرنا

دستی کنٹرول

• دبائیں سب سے اوپر of the paddle to turn the connected load ON.
• دبائیں نیچے of the paddle to turn the connected load آف.

Z-Wave کنٹرول

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

دیکھ بھال

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• صفائی: سوئچ صاف کرنے کے لیے اسے نرم سے صاف کریں، ڈیamp کپڑا کھرچنے والے کلینر یا سالوینٹس کا استعمال نہ کریں۔
• فرم ویئر اپ ڈیٹس: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• عمومی دیکھ بھال: اس بات کو یقینی بنائیں کہ سوئچ ضرورت سے زیادہ نمی یا انتہائی درجہ حرارت کے سامنے نہ آئے۔

خرابی کا سراغ لگانا

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle ایک بار. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

وضاحتیں

وارنٹی اور سپورٹ

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webسائٹ یا ان کے کسٹمر سروس ڈیپارٹمنٹ سے رابطہ کریں۔

Webسائٹ: www.gocontrol.com

مینوفیکچرر: GOCONTROL