مائرز HJ50D کنورٹیبل ڈیپ واٹر ویل جیٹ پمپ صارف دستی

1. پروڈکٹ ختمview

The Myers HJ50D is a convertible deep water well jet pump designed for reliable water supply from deep well applications. This 1/2 HP pump operates on either 115V or 230V, providing versatility for various electrical setups. It is engineered for efficient performance in residential and light commercial water systems.

• Deep Water Well Jet Pump functionality.
• 1/2 Horsepower motor for effective water transfer.
• دوہری جلدtage operation: 115V or 230V.

An image showing the Myers HJ50D Convertible Deep Water Well Jet Pump, a green-colored unit with a motor on one end and the pump housing with inlet/outlet ports on the other. This pump is designed for deep well applications.

2. حفاظتی معلومات

Read and understand all safety instructions before installing, operating, or performing maintenance on this pump. Failure to follow these instructions can result in serious injury, death, or property damage.

• برقی خطرہ: Always disconnect power before servicing the pump. Ensure proper grounding and wiring according to local electrical codes.
• دباؤ کا خطرہ: Water systems operate under pressure. Relieve system pressure before servicing.
• حرکت پذیر حصے: آپریشن کے دوران ہاتھوں اور کپڑوں کو حرکت پذیر حصوں سے صاف رکھیں۔
• گرم سطحیں: The pump motor can become hot during operation. Allow it to cool before handling.
• قابل عملہ: Installation and electrical connections should only be performed by qualified personnel.

3. سیٹ اپ اور انسٹالیشن

3.1 پری انسٹالیشن چیک

• Verify the power supply matches the pump's voltage کی ضروریات (115V یا 230V)۔
• Ensure the well casing is clean and free of debris.
• Confirm adequate space for pump installation and future maintenance.

3.2 پمپ لگانا

Mount the pump on a firm, level foundation to minimize vibration. Use appropriate bolts and washers to secure the pump base. Ensure the pump is as close to the well as practical to reduce suction lift.

3.3 پلمبنگ کنکشن

1. Connect the suction line from the well to the pump's suction port. Ensure all connections are airtight to prevent air leaks.
2. Connect the discharge line from the pump to the pressure tank and distribution system.
3. Install a check valve in the suction line if not already present in the jet assembly.
4. Install a pressure gauge and pressure switch on the discharge side.

3.4 الیکٹریکل وائرنگ

Wire the pump according to the wiring diagram provided on the motor nameplate and local electrical codes. Ensure the correct voltage selection (115V or 230V) is made before connecting power. The pump must be properly grounded.

3.5 پمپ پرائمنگ

Before initial startup, the pump casing and suction line must be completely filled with water. Remove the priming plug, slowly fill the pump with water until it overflows, then replace the plug securely. This process removes air from the pump, allowing it to create suction.

4. آپریٹنگ ہدایات

4.1 ابتدائی آغاز

1. Ensure the pump is properly primed as described in Section 3.5.
2. Open a faucet in the system to allow air to escape.
3. Restore power to the pump. The pump should start and begin to draw water.
4. Once a steady stream of water flows from the faucet, close the faucet. The pump will build pressure and shut off when the pressure switch setting is reached.

4.2 عمومی آپریشن

The pump will automatically cycle on and off based on the pressure switch settings, maintaining system pressure as water is used. Monitor the pressure gauge periodically to ensure proper operation.

4.3 پمپ کو بند کرنا

To temporarily or permanently shut down the pump, disconnect the electrical power supply at the circuit breaker or fuse box. If shutting down for an extended period or for winterization, refer to the maintenance section.

5 دیکھ بھال

Regular maintenance ensures the longevity and efficient operation of your Myers HJ50D pump. Always disconnect power before performing any maintenance.

5.1 باقاعدہ معائنہ

• Check for leaks around plumbing connections.
• Inspect electrical wiring for signs of wear or damage.
• آپریشن کے دوران غیر معمولی آوازیں سنیں، جو کسی مسئلے کی نشاندہی کر سکتی ہے۔
• Verify the pressure switch is operating correctly and maintaining desired pressure.

5.2 موسم سرما

In areas subject to freezing temperatures, the pump and associated piping must be drained to prevent damage. Disconnect power, open drain plugs on the pump and any exposed piping, and allow all water to drain completely. Store the pump in a warm, dry place if possible, or ensure it is thoroughly drained and protected from freezing.

6 خرابیوں کا سراغ لگانا

This section provides solutions to common operational issues. For problems not listed or if solutions do not resolve the issue, contact a qualified service technician.

7. وضاحتیں

8. وارنٹی اور سپورٹ

For detailed warranty information, please refer to the warranty card included with your product or visit the official Myers webسائٹ وارنٹی دعووں کے لیے خریداری کے ثبوت کے طور پر اپنی خریداری کی رسید رکھیں۔

For technical support, replacement parts, or service inquiries, please contact Myers customer service. Contact details can typically be found on the manufacturer's webسائٹ یا مصنوعات کی پیکیجنگ میں۔