SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. تعارف

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

شکل 1.1: سامنے view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. حفاظتی معلومات

• تنصیب اور آپریشن سے پہلے تمام ہدایات کو احتیاط سے پڑھیں۔
• بجلی کی فراہمی والیوم کو یقینی بنائیںtage matches the device's requirements (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Do not operate the device in environments with excessive moisture, dust, or corrosive gases.
• Disconnect power before performing any maintenance or wiring changes.
• Keep the device away from strong electromagnetic interference.

3. مصنوعات کی خصوصیات

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Wide operating temperature range.
• Compact and easy-to-install design.

4. پیکیج کے مشمولات

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 ایکس یوزر مینوئل (یہ دستاویز)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. سیٹ اپ

5.1 چڑھنا

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 وائرنگ

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Terminals 1 & 2: AC Power Supply (85-265V AC, 50/60Hz)
• Terminals 3 & 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Terminals 6 & 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Terminals 11 & 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. آپریٹنگ ہدایات

6.1 ڈسپلے ختمview

The meter features a dual display:

• PV (عمل کی قیمت): The upper red display shows the current measured temperature/humidity.
• SV (قدر مقرر کریں): The lower green display shows the desired set point.
• آؤٹ اشارے: Illuminates when the main output is active.
• AT اشارے: Illuminates when the auto-tuning function is active.
• AL1/AL2 Indicators: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 بٹن کے افعال

• سیٹ بٹن: Used to enter parameter setting mode and confirm selections.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (نیچے) بٹن: Decreases the value of a parameter or set point.
• ▲ (اوپر) بٹن: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. عام آپریٹنگ موڈ میں، دبائیں۔ سیٹ ایک بار بٹن. SV ڈسپلے چمکنا شروع ہو جائے گا۔
2. استعمال کریں۔ ▲ (اوپر) اور ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. دبائیں سیٹ button again to confirm the new SV and exit the setting mode.

6.4 Advanced Parameter Settings

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the سیٹ button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (اوپر) اور ▼ (Down) buttons to navigate through parameters and the سیٹ button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7 دیکھ بھال

• صفائی: ڈسپلے کو صاف کریں اور casing ایک نرم، خشک کپڑے کے ساتھ. کھرچنے والے کلینر یا سالوینٹس کا استعمال نہ کریں۔
• معائنہ: Periodically check wiring connections for looseness or corrosion.
• ذخیرہ: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8 خرابیوں کا سراغ لگانا

9. وضاحتیں

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. وارنٹی اور سپورٹ

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webرابطے کی معلومات کے لیے سائٹ۔